Pay in installments of $49.38 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Aug 6 - Aug 11
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
aFe Magnum FORCE Open Element Intake GM Silv/Sierra 1500 14-18 / Silv LD/Sierra Limited 2019 V8This 9 tall 360 degree radial flow air filter features a 5" flange and our oil free Pro DRY S media with three layers of synthetic media for maximum convenience. Its progressive layering provides great filtration efficiency and dust holding capacity, while not requiring the use of oils. This media is best suited for street use. Its inverted top makes for more filter surface area, resulting in longer service intervals. The included performance air
This 9” tall 360-degree radial flow air filter features a 5" flange and our oil-free Pro DRY S media with three layers of synthetic media for maximum convenience. Its progressive layering provides great filtration efficiency and dust holding capacity, while not requiring the use of oils. This media is best suited for street use. Its inverted top makes for more filter surface area, resulting in longer service intervals. The included performance air filters are surrounded by open-element XLPE (cross-linked polyethylene) polymer housings that minimize warm engine air for maximum performance. The open design allows for easy viewing of the air filter and delivers an aggressive intake induction sound. This system features a high quality, computer-designed, dyno-tuned intake tube to achieve maximum power gains while maintaining a perfect fit. The XLPE material is heat soak resistant and extremely durable. This is a direct fit intake system that utilizes factory mounting points and requires no cutting or modifications. All necessary clamps, couplings, and hardware are included. Its revolutionary design, featuring our patent pending filter-to-housing interface, uses half the number of parts of a traditional cold air intake system.This Part Fits:
| Year | Make | Model | Submodel |
|---|---|---|---|
| 2016-2021 | Chevrolet | Silverado 1500 | Custom |
| 2014-2021 | Chevrolet | Silverado 1500 | High Country |
| 2015-2018 | Chevrolet | Silverado 1500 | LS |
| 2014-2021 | Chevrolet | Silverado 1500 | LT |
| 2014-2021 | Chevrolet | Silverado 1500 | LTZ |
| 2015-2021 | Chevrolet | Silverado 1500 | SSV |
| 2014-2021 | Chevrolet | Silverado 1500 | WT |
| 2019 | Chevrolet | Silverado 1500 LD | Custom |
| 2019 | Chevrolet | Silverado 1500 LD | LT |
| 2019 | Chevrolet | Silverado 1500 LD | WT |
| 2021 | Chevrolet | Suburban | LS |
| 2021 | Chevrolet | Suburban | LT |
| 2021 | Chevrolet | Suburban | Premier |
| 2021 | Chevrolet | Suburban | Z71 |
| 2021 | Chevrolet | Tahoe | LS |
| 2021 | Chevrolet | Tahoe | LT |
| 2021 | Chevrolet | Tahoe | PPV |
| 2021 | Chevrolet | Tahoe | Premier |
| 2021 | Chevrolet | Tahoe | SSV |
| 2021 | Chevrolet | Tahoe | Z71 |
| 2014-2021 | GMC | Sierra 1500 | Base |
| 2014-2021 | GMC | Sierra 1500 | Denali |
| 2014-2021 | GMC | Sierra 1500 | SLE |
| 2014-2021 | GMC | Sierra 1500 | SLT |
| 2019 | GMC | Sierra 1500 Limited | Base |
| 2019 | GMC | Sierra 1500 Limited | SLE |
| 2021 | GMC | Yukon | SLE |
| 2021 | GMC | Yukon | SLT |
| 2021 | GMC | Yukon XL | SLE |
| 2021 | GMC | Yukon XL | SLT |
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.2 ★★★★★
Based on 25 reviews
Sort
Product Reviews
★★★★★ 5
Rock-solid tall mount to hold a monitor above a large monitor
Size: 13"-32", Style: Single, Size: 13"-32", Style: Single
I bought the 31.5 model to mount a 27" monitor above a 32" monitor on my desk. This is the first monitor mount I have ever purchased and I am thrilled with the entire mount! The installation instructions were simple to follow. All hardware was clearly notated and packaged by part number. The mount holds the 27" monitor (which isn't all that light) perfectly above my desk monitor and is very stable. Adjustment is easy and effective and It doesn't wobble one bit.
The cable routing clips work well and are literally a snap to install. I used the clamp mount but a screw-down desk mount is included.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 31, 2025
★★★★★ 5
Quality Stand
Size: 13"-27", Style: Triple
Solid, heavy duty and well made. I purchased this as I was adding a third monitor to my setup. So I had to choose between buying a 2nd mount that had one arm on it, or just replace my 2 arm setup with a single 3 arm setup. I'm glad I went this route. Very easy to assemble and it feels heavy duty. I've been using it daily for about 2 months now and it's held up perfectly. Zero issues with assembly and the instructions are well written. The mount options are solid and the metal is thick. Quality product at an amazing price.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on August 11, 2025
★★★★★ 4
Overall, very good for the price.
Size: 13"-32", Style: Single, Size: 13"-32", Style: Single
For the price, I’m pleased with it.
Overall, it’s a sturdy stand with quality machining. All the screws went in easily, poorly machined products have crooked holes or bad threads. The mount base comes with 2 types, standard mount for a desktops surface. The other one is for desktops with monitor holes/cabling drilled through them. All the parts are heavy gauge and I encountered no difficulty during assembling.
There seems to be a tension screw for the tilt feature. I had to tighten the screw that holds the tilt joint together because out of the box, the monitor flopped forward hard. I had to be mindful while mounting it to the main arm so it wouldn’t slam into my glass desktop.
The 2 arms that allow you to move the monitor forwards and back, left and right were a little stiff, I loosened the screw a bit on the main arm, at the pole. That seemed to be all that was required. I tried to loosen the bolt where the 2 arms meet, and it wouldn’t budge. I didn’t force the issue.
The instructions were adequate for assembly without covering anything else, like adjusting the tilt bolt for the weight of the monitor.
So, while I think this was a good mount for the investment, there are tradeoffs to mention.
I’m accustomed to swinging my monitors upward and dusting underneath them. Height is fixed by a screw on this one.
I was struggling to install the monitor cables when I realized you can tilt the bottom toward you until the top or the monitor hits the pole, or, until it’s sitting nearly flat like a table. Elevated several inches above the desktop. I consider this a Pro / Con feature.
Where the arm ties into the VESA mount, the fit is a little sloppy. It’s not a safety concern but I can wiggle the monitor backwards and forwards at the outer edges “About ¾ inch “before feeling any resistance from the mount. Same goes for tilting. I don’t see this as much of an issue. Normally, I don’t foresee any outside forces acting in the monitor to create a problem. However, there’s room for improvement. The rest of the machining seemed steller.
I have multiple computers in different rooms. 32” monitors are used as primary monitors with 32” to 23” as secondaries.
I like mine roughly 1” above the desk. That places the top of the monitor at my eye level and the ideal viewing angle.
I have fully articulated, hydraulic mounts on most of my monitors. Nice ones for large heavy monitors run $75 to $100 and up.
I paid $36 for this one. The……… WALI Monitor Arm Mount for Desk, Single Extra Tall Computer Desk Mount, Monitor Bracket Mount Stand Single, up to 32 inch, 22 lbs (M001XL), Black.
Amazon lumps the reviews of similar products together, so I specified which mount I purchased.
I’m using this one on a glass desktop, I’m attaching it to the same point I constructed from wood for a different mount. It didn’t lower the monitor low enough either. So, the top of that mounting point is 4” lower than the surface of the glass top.
Despite being that low, I didn’t actually need the 32” pole / monitor mount, the 16” model would have worked.
There’s still 2” of pipe available above the arm. The 32” was on sale & I didn’t know if the 16” would suffice. The pole is a screw together 2 piece. I unscrewed / removed the other pole as it looked out of place in my dual computer setup.
That leaves a hole in the top of the pipe / mount. I wish they included a cap for that. The top pipe has a cap but of a different diameter.
I’d like to give it 4 ½ Stars but Amazon won’t let me. I’ve got to go with 4.
Height adjustments with heavy monitors and an Allen wrench can present a challenge, it’s the nature of the beast and I won’t give it 5 stars for a few reasons. The sloppy VESA mount and loose tilt motion. No instructions that cover that, or if I was supposed to loosen the arm at the pole to improve motion.
I would recommend this mount to others.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on July 18, 2024
★★★★★ 5
Excellent mount, especially if you want your monitor mounted higher above the desk.
Size: 13"-32", Style: Single
This is the monitor mount I should have had all along. The extra tall pole allowed me to mount my 32" monitor at the correct height (something I couldn't do with the spring-mount I previously had. It came with good directions, everything needed for install except for a Phillips head screwdriver and a 10mm wrench for one cap nut. The arm that holds the monitor is highly adjustable, and once everything is tightened down, very sturdy. I recommend this one without reservations.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 1, 2026
★★★★★ 5
Easy and Functional for 3 Monitor Setup
Size: 13"-27", Style: Triple
Some assembly required. Used this to re-configure my 3 monitor setup. 2 27" monitors across the bottom and a 20-ish" monitor up top. First and foremost, anything bigger than 27" on the bottom two and it will not work. The span was just barely long enough for my application and still allow for any articulation of the monitors. I would prefer to have them angle towards me just a little more, but it works. Assembly was straight-forward. Instructions were pretty clear as far as the pictures go. I didnt actually read the text, but thats pretty much how obvious it is to assemble and mount the monitors. The tubing and clamps feel heavy-duty. With the exception of a drill, drill bits, and phillips head screw driver, they provide the tools and hardware necessary to assemble, mount and adjust the monitors, to include longer screws and offsets for the monitors if required.
Installation on my desk went well. I used the through hole option strictly due to the desk not being able to accomodate the clamp. Word of caution... with all three monitors hung on the mount, this thing is HEAVY and all supported by just the main tube. If you use the clamp option, make sure your desktop/tabletop will allow the clamp to fully seat. Otherwise, you run the risk of it slipping loose and you'll be wearing the monitors if you happen to be sitting in front of them when it comes down.
Once all the monitors are mounted, the overall setup is surprisingly sturdy considering the size of the main support tube. Yes, it will wobble some, but overall, it works pretty well and once the clamps are locked into place the monitors stay in place. Took a couple of hours for me to get it all set up, but it could be done quicker I'm sure.
All in all, me likey!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 13, 2022
recommand products
All Balls Racing 12-13 Kawasaki Teryx 750 4x4 8 Ball Axle Rear Left
113.97
All Balls Racing 10-14 Ranger 400 4x4/11-13 Ranger 500 4x4/11-13 Ranger 500 4x4 Crew Axle
127.25
All Balls Racing 07-10 Suzuki LTA-450 X King Quad 8 Ball Axle Front Left
113.97
All Balls Racing 2020 Polaris General XP 1000 EPS 8 Ball Axle - Rear Left
119.67
All Balls Racing 00-05 TRX 350 FE/00-05 TRX 350 FM Axle
114.90