Pay in installments of $8.75 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Aug 7 - Aug 12
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
PYRODRONE F4 RACE with VTX PIT mode - 30x30mmIt's finally here! The pyrodrone F4 board has been one of the very few boards with perfectly flat one side which lot of guys been utilizing as a "shelf" for their VTX and RX. It was time to reroute the pads and offer a direct clean solder option for the TBS UNIFY V3 VTX and the TBS Nano RX similar to the Whitenoise Synergy FC. The Pyro F4 RACE also has a built in socket which makes it plug & play with the Pyro32 F3 45A 4in1 ESC (The correct harness is
It's finally here!
The pyrodrone F4 board has been one of the very few boards with perfectly flat one side which lot of guys been utilizing as a "shelf" for their VTX and RX.
It was time to reroute the pads and offer a direct clean solder option for the TBS UNIFY V3 VTX and the TBS Nano RX similar to the Whitenoise Synergy FC.
The Pyro F4 RACE also has a built in socket which makes it plug & play with the Pyro32 F3 45A 4in1 ESC (The correct harness is ONLY included in the ESC package)
Please check below for tips and Betaflight Settings.
- MPU6000 Gyro STM32F405 CPU @ 168mhz, can be overclocked
- 2-6S direct battery input
- 3.3V 100ma, 5V 2A BEC
- 5V and Vbat Camera Power
- Built in configurable Betaflight OSD
- Flat bottom PCB for SUPER CLEAN builds
- 36x36 PCB with 30.5x30.5 mounting holes
- 6 UARTS.
- UART1 (INVERTER FOR SBUS),
- UART2 (FREE),
- UART3 (INVERTED TELEMETRY), use CLI command : Set tlm_halfduplex=off UART4 (Free),
- UART5 (Smart Audio)
- UART6 (Free)
- The Pyrodrone F4 RACE flight controller can power HV VBAT or 5V Video transmitters.
- BF Target: PYRODRONEF4
Please make sure to jump the correct selection for your VTX.
resource pinio 1 A15 (Hit Enter)
Set pinio_box = 39 (Hit Enter)
Assign a switch to the VTX PIT option in Betaflight MODES tab.
If VTX PIT mode is NOT needed then just solder your VTX and fly! (no additional settings needed)
If you want to solder the TBS UNIFY 5V direct to the board which is where this FC REALLY shines then here are couple tips for you.
Using the TBS Direct mount feature means you have to flip the board upside down with the USB to the left side of the drone.
SO REMEMBER to change the board orientation in Betaflight configuration tab.
Both the VTX and the board have "anchor" Pads on both sides of the VTX, but we do not recommend using all these anchor points for easier future maintanence in case you ever have to remove the VTX.
Here is what we recommend.
Use a very thin piece of the double sided tape that is provided in your TBS UNIFY V3 package and apply it on the VTX as shown in the below picture.
This will work as a place holder for you to line up and solder the 4 points.
Once lined up solder the 4 points.
The board is labled for TBS NANO RX as the holes perfectly line up with the Nano RX, but you can really use any RX and just choose the correct type of receiver in the Betaflight configuration page.
Our preferred way of mounting the RX is with silicone wires rather than direct solder, Again for easier future maintenence purposes.
Please check the below picture:
For correct voltage reading change the Voltage scale value to 160
If you charge your batteries over 4.20 per cell AKA HV then remember to adjust the Maximum Cell Voltage to 4.4 otherwise the average cell voltage will read wrong on your OSD.
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy